Features of 4LEDs High Voltage Matrix LED Modules
1. Direct AC110V/220V Input Without a Separate DC Power Supply
The YS-MB8747 and YS-MB8746 are designed for high-voltage AC input, supporting AC220V and AC110V respectively. Direct mains operation can simplify the electrical architecture by removing the need for an external low-voltage power supply, which is particularly useful when large numbers of modules are installed across commercial signage systems. Similar high-voltage LED modules are commonly marketed around direct AC connection and simplified installation.
2. 4-SMD3030 LED Configuration with 300–360lm Output
Each module integrates four SMD3030 LEDs and delivers approximately 300–360 lumens, providing a strong light source within the 68 × 68 × 8.3 mm matrix-style housing. The output level is suitable for illuminated letters and light box structures that need substantial brightness from each module.
3. Built-In Constant-Current IC for Stable Operation
The module integrates a constant-current control IC, helping maintain stable LED output under the rated operating voltage. This is particularly important in high-voltage signage systems, where consistent current control is required across multiple connected modules.
4. High-Voltage Cascade Capability Up to 100 Modules
One of the key advantages of this series is its high cascade capacity, with the maximum quantity reaching 100 modules. This can simplify power distribution and reduce the amount of low-voltage wiring and external power equipment needed for large illuminated sign installations.
4LEDs High Voltage Matrix LED Modules Dimensions
4LEDs High Voltage Matrix LED Modules Typical Lighting Test Data
Built around our high Voltage Matrix LED Modules, the figures below show how spacing, module count and surface brightness shift as you adjust light box depth. These modules run on AC110V/220V with a 175° wide beam angle and IP65 rating, so the same layout logic holds up across indoor retail displays and outdoor storefront signs alike. Whether you're laying out a backlit airport sign, a subway light box or a slim retail display, matching DX/DY to box thickness keeps the face evenly lit without overloading it — thicker boxes can use wider spacing and fewer modules per square meter, while thinner builds need tighter pitch to avoid hotspots. The table also lists wattage per m², so you can estimate total power draw and transformer sizing upfront instead of guessing later. Bottom line: you get clean, consistent output across the whole sign face and a tighter bill of materials.
| Light Box Thickness(mm) | Module Spacing(mm) | Installation density(PCS/m²) | Surface illumination(Lux) | Power per square meter(W/㎡) |
| 100 | DX=400, DY=400 | 6.25 | 800~1200 | 25 |
| 120 | DX=450, DY=450 | 4.5 | 600~1000 | 18 |
| 130 | DX=500, DY=500 | 4 | 500~900 | 16 |
4LEDs High Voltage Matrix LED Modules Wiring Diagram & Installation Guide
Note:
1. Maximum cascade connection is 60pcs at AC110V
2. Maximum cascade connection is 120pcs at AC220V
Single-ended power supply
Installation Notes
1. This module uses AC power (AC 220V) directly, no need to buy power supply, easy to install
2. After installation, when the voltage is turned on, do not touch the module with metal or hands
3. It is best to use terminal wiring when connecting to the power supply. Double-terminal power supply is prohibited
4. The outlets at both ends of the module should be waterproofed and leak-proofed
5. A leakage switch or a controller switch (with short circuit protection and overload protection) must be used
6. The installation surface must be flat, clean and dry
7. When installing wiring, it is forbidden to operate with power on
8. Avoid rain and mechanical vibration during transportation
Recommended Applications for 4LEDs High Voltage Matrix LED Modules
1. High-Voltage Channel Letter Systems
The direct AC design makes this matrix module particularly useful for channel letters and illuminated dimensional signs where a large number of LED modules may need to be powered across the same sign structure. Removing separate DC power supplies can help simplify the overall electrical design.
2. Large Single-Sided Advertising Light Boxes
Designed for 10–20cm deep single-sided light boxes, the 175° beam angle allows the module to spread light across the available cabinet depth while the 300–360lm output provides a strong illumination source for advertising graphics.
3. Shopping Mall and Commercial Signage
Suitable for illuminated retail signs, shopping mall branding, commercial building identification and promotional displays. The high-voltage architecture can be useful for projects where multiple modules are arranged across a large sign.
4. Exterior Building and Corporate Signs
Packaging & Shipping Information for 4LEDs High Voltage Matrix LED Modules
| Item No. | Qty Per String（PCS） | Quanty(Pack) | Total Qty(Pcs) | Total Weight(Kg) | Quter box size(mm) | ||
| L | W | H | |||||
| YS-MB8747/YS-MB8746 |
10 |
50 |
600 | 30 | 520 | 300 | 360 |
Professional 4LEDs High Voltage Matrix LED Modules Manufacturer & Supplier
Founded in 2013, YESUN LED is a Shenzhen-based manufacturer specializing in LED signage and commercial lighting solutions. With 5,000㎡ of automated factory space, dedicated SMT lines, and strict full-process QC, we support OEM/ODM projects for customers in over 100 countries. To learn more about our team, factory, and production capabilities.
Product Certifications & Compliance
Our products comply with international standards including UL, ETL, CE, and RoHS certifications to support different market requirements.
4LEDs High Voltage Matrix LED Modules Quality Control Process
We apply strict quality inspection standards throughout production to ensure stable performance and reliable quality before shipment.
